User:Tingo

Tingo
Real name:	Torfinn Ingolfsen
Role:	Geek and Jack-of-all-trades

Back in old times, I was a user of ND machines, Sintran III, Tandberg terminals (I even did repairs on the terminals) and more. Later I was also a System Operator of ND machines. These days, I am the proud caretaker of a working ND-Satellite/9. You can read more about it on my worklog for the machine: ND 900-135.

The ND-100/CX worklog is here: ND 3392-1669

Contact info (protected email address): http://scr.im/1w02

Subpages: Collection, Documentation, Floppy machines, Tips, Testing, sg3_utils, setblocksize,

Wanted

Stuff I am looking for

2016-09-01: internal SCSI cables (ones with 50 pin IDC plugs on each end), both long and short ones.

2016-05-28: a way to

• read CDC 848-24 / 9848-24 cartridge disks
• read (magnetic) tape, probably 9 track CCT

2011-12-20: I am looking for a 3094 Ethernet II Controller (and internal cabling) for the ND-100/CX machine.

Ideas

2018-03-29: perhaps the FlashFloppy firmware could be enhanced to support ND formats so we can use a Gotek drive as a floppy drive on ND machines.

history

2016

2016-10-04: I did some testing of nd100em, and set up a personal worklog page for it.

2016-09-29: the package from AmigaKit.com (SCSI cables) arrived.

2016-09-23: noticed that AmigaKit.com has SCSI cables, so I ordered a few.

2016-09-22: the SCSI2SD v5 package arrived.

2016-09-06: the utility setblocksize managed to change the ST31200N drive to 1024 bytes block size, check out the setblocksize subpage.

2016-09-05: I ordered a SCSI2SD v5 from itead (China).

2016-09-04: tried to reformat a SCSI hard drive from 512 byte blocks to 1024 byte blocks with sg_format from sg3_utils. It didn't end well, check out the sg3_utils subpage.

2016-07-28: more magnetic tapes, paper tapes and documentation rescued today.

2016-07-14: a large haul again. Today I got a Facit 4070 paper tape punch, a Facit 4012 (paper) tape winding machine, a Digitronics paper tape reader (it needs a new rubber roller wheel). I got 1 x CDC disk pack 75 MB labeled "Back-up S80A", "800516", 1 x paper tape (green) with unknown code on it (no marks or labels), 3 x rolls of "blank" paper tape (green) + blank tape (green) in Facit 4070 and a lot of documentation.

2016-06-30: Gandalf and a friend delivered me a ND110-Satellite and a Nokia VDU 301 S terminal.

2016-05-28: a large haul today - I got 5 disk cartridges (CDC 9848-24), 9 tapes (the tape is 0.5 inch wide, the spools are around 7 inches in diameter, perhaps this is 9 track CCT?), 1 paper tape (containing RUNOFF:SYMB) and a lot of documentation.

2016-05-24: finished getting NDwiki to run on the new server (with lots of help from Mike and Gandalf).

2016-05-19: I set up a server to run NDwiki on.

2011

2011-11-10: ND-100/CX - testing the machine with the newly fixed drive; after pressing "START" the "RUNNING" light comes on, and after a while the machine boots into Sintran (SINTRAN III - VSX / 500 K). Happy day!

2011-11-10: ND-100/CX - today I fixed the hard drive (a ST-506 drive, Micropolis 1325); it had the "sticky bumper" problem; end stops for the head assembly is made of rubber, which turns sticky after many years. The result is that the head can't "unstick" itself when the drive is powered up. And since the drive doesn't get track 0 (zero) it turns itself off after about a minute. Putting a piece of paper (a thin strip from a post-it note) between the "sticky bumper" and the head assembly fixed that.

2011-10-10: More testing of the ND-100/CX today. The hard drive doesn't respond at all - perhaps the motor isn't spinning at all?

2011-09-23: Today I got a ND-100/CX Compact machine and a Tandberg TDV2200/9 terminal delivered to my apartment! Thanks!. The key switch on the panel is broken, hard drive drive doesn't seem to work, and I don't have any 5.25 inch ND floppies, but I am still very happy.

2010

2010-12-03: I tested and verified the (serial) terminal ports on the back of the machine. Terminal 48 - 51 (ports 6 - 9) are set to current loop, and all works. Terminal 36 - 39 (ports 2 - 5) are set to RS-232, but only terminal 38 and 39 are working

2010-12-03: The machine now boots straight into SINTRAN III (from hard drive) when powered on. Yay!

2010-11-29: The ND-Satellite/9 boots SINTRAN III again; this is the first time since I got the machine.

2010-10-24: my contributions to this site (if any) can be licensed under any license Mike wants to use. Torfinn 15:45, 24 October 2010 (UTC)

2010-10-23: it seems like the winchester disk in the ND-Satellite/9 doesn't want to play. Everything powers up, and the drive is spinning, but I get errors when trying to read from it.

2010-10-22: I got myself a ND-Satellite/9 machine, two terminals (ND 320 and ND 246), two boxes of floppies (8 inch) and some manuals from a nice fellow in town. Cool!

Various links

Just various ND-related links that I have found and want to find again.

See my links page: User:Tingo/Links