View source for SCSI-TV

SCSI-TV.

{{Stub}}
== Description ==
Test program for the Floppy/SCSI print (SCSI part only) and SCSI devices connected to the bus<ref>[[ND-210523G]] program description, page 35</ref>.

== Supported products ==
Products supported by version B.
<pre>
Vendor   Product          Device type
NDMICROP 1375             Direct
TANDBERG TDC 3600         Sequential (streamer)
OSI      LD 1200 SCSI     Write Once (optical disk)
NDCDC    EMD 97201 (736)  Direct
NDCDC    EMD 97201 (368)  Direct
NDSTK    2925             Sequential (magtape)
ARCHIVE  VIPER 150 21247  Sequential (streamer)
</pre>

== Commands ==
 >CLEAR-DEVICE
This command will perform a bus reset on the selected SCSI bus. Can be used in "hang" situations.

 >DECODE <Item>
This command can decode some SCSI items.

 >DUMP-SENSE-DATA

 >LIST-DEVICES
This command will list all SCSI host adaptors in ND-100 an the connected devices along with some important device information.

 >PRINT-TAPE-STATISTICS

 >RUN-ADAPTOR-TESTS <Test list>

 >RUN-DEVICE-TESTS <Test list>

 >SELECT-DEVICE <Adaptor name> <Id number>
This command select the SCSI host adaptor and SCSI device to operate on. The commands "RUN-ADAPTOR-TESTS" and "RUN-DEVICE-TESTS" will use this selected device.

Legal answers for adaptor are:
* Adaptor name (ADAPTOR-n, n=1:4).
* Adaptor number (1:4).
* Logical device number for adaptors data field (2202B:2205B).
* Hardware device number for adaptor (144300B, 144400B, 144500B, 144600B).

Legal answers for ID numbers are 0:7. ID number 7 is normally the SCSI host adaptor, and ID 0 is normally equivalent to "DISC-SCSI-1" which is the boot disk.

 >SET-BUFFER-LIMITS
The operator may set first and last memory page for the DMA buffer (only used when the host adaptor is placed in MULTIPORT-4).

 >SET-PARAMETERS <Loop mode> (<Loop count>) <Abort mode> (<Abort count>) <Supress mode>
This command will set parameters for execution of the commands "RUN-ADAPTOR-TESTS" and "RUN-DEVICE-TESTS".

 >SET-TAPE-PARAMETERS
Change the default parameters for the write/read magtape test (test number 20) and the write/read streamer test (test number 30). (Only available when a sequential device is selected).

 >TAPE-SERVICES
This command performs some useful magtape/streamer services (LOAD, UNLOAD and REWIND).(Only available when a sequential device is selected).

 >PROGRAM-STATUS (TPE command)
This will include the values of some flags in the program.

== Tests ==

=== Host adaptor tests ===
Adaptor tests available:
# Registers write/readback
# Control/Status
# DMA in test mode
# Interrupt at level 11
# NCR chip self diagnostic test
# NCR chip SCSI commands/status

=== Device tests ===
Device tests available:

Device controller tests
# Drive contact
# Basic drive self test
# Extended drive self test
# SCSI bus data transport
# SCSI bus stress

Disk tests (none destructive)
{{ordered list|start=10
| Seek min/max
| Random seek
| Write/read scratch
| Random read
| Random read data partition - write scratch
}}

Magtape tests
{{ordered list|start=20
| Write/read magtape
| BOT test
| Wear test
| Filemark test
}}

Streamer tests
{{ordered list|start=30
| Write/read streamer
| Over/under run
| Filemark/space test
}}
== Known versions ==
; B00 : found on [[ND-210523G]]

; C00 : found on [[ND-210523H]]

== References ==
<references/>

[[Category:Norsk Data software]]