ND-211056A: Difference between revisions
(created ND-211056A page) |
(→Installation: added installation procedure) |
||
| Line 21: | Line 21: | ||
== Installation == | == Installation == | ||
The system may be delivered on: | |||
* A - 1.2 Mbyte, 8 inch or 5 1/4 inch double-sided diskettes | |||
or | |||
* B - 0.3 Mbyte, 8 inch single-sided diskettes | |||
Use the same kind of diskettes ("A" or "B") throughout the whole installation procedure. You may install (1) the SPRINT basic modules with desired language, (2) add desired language to existing SPRINT or (3) change the number of printer control modules. The installation procedure is fully interactive, which means that once started, it will continuously check the operation. It will inform the operator if any error(s) occurs and of what to do to proceed. | |||
The operator is also asked some questions about the specific configuration. By typing '?' and ENTER some additional information is provided. | |||
=== How to start the installation === | |||
- The installation must be run from SINTRAN. | |||
- Log in as SINTRAN user name SYSTEM. | |||
- Insert the diskette containing the directory name 211056A<rev>-<lang>-01 into the diskette station. | |||
- Execute these commands (operator input is underlined and parameters are enclosed in single brackets): | |||
@<u>ENTER-DIRECTORY,211056-<lang> FLOPPY-DISC-<drive> <floppy unit></u> | |||
@<u>(211056:FLOPPY-USER)SSY-INST-A</u> | |||
The installation procedure will now start. It is self-explanatory. | |||
=== How to update your HENT-MODE, LOAD-MODE and STOP-MODE files === | |||
When you install the system, remember to insert | |||
@MODE (ND-OPERATIONS)SPRINT-LOAD:MODE,, | |||
in your HENT-MODE file, and | |||
@SPRINT /STOP-SPRINT | |||
in any STOP-MODE files, and | |||
@SPRINT /START-SPRINT | |||
in your LOAD-MODE file, after the START-SPOOLING commands, but before any appending of SETUP-files for the printers (this is important because otherwise the running of SETUP will be aborted and the printer will be incorrectly initialized). NOTE: Remember to run SETUP-files with status 'UNCONVERTED' if you append them to the SPRINT-queues. | |||
== Date == | == Date == | ||
Revision as of 11:59, 13 September 2016
SPRINT Spooling System
Description
 |
This article is a stub. You can improve NDWiki by expanding it. |
Prerequisites
The following are required in order to use this product.
Hardware
Computer: ND-100.
Software
Operating system: SINTRAN III-VSE K patchfile >= 1000 or SINTRAN III-VSX K patchfile >= 3000 or SINTRAN III-VSE/VSX-J patchfile >= 12000
Other: ND-210373I X-MESSAGE
Documentation
PD- or PI-sheet
- Program Description ND-211056A.pdf
Manuals
- Norsk Data Document ND–60.252.1 EN THE SPRINT USER GUIDE
- Norsk Data Document ND–60.252.1 NO THE SPRINT USER GUIDE
Installation
The system may be delivered on:
- A - 1.2 Mbyte, 8 inch or 5 1/4 inch double-sided diskettes
or
- B - 0.3 Mbyte, 8 inch single-sided diskettes
Use the same kind of diskettes ("A" or "B") throughout the whole installation procedure. You may install (1) the SPRINT basic modules with desired language, (2) add desired language to existing SPRINT or (3) change the number of printer control modules. The installation procedure is fully interactive, which means that once started, it will continuously check the operation. It will inform the operator if any error(s) occurs and of what to do to proceed.
The operator is also asked some questions about the specific configuration. By typing '?' and ENTER some additional information is provided.
How to start the installation
- The installation must be run from SINTRAN.
- Log in as SINTRAN user name SYSTEM.
- Insert the diskette containing the directory name 211056A<rev>-<lang>-01 into the diskette station.
- Execute these commands (operator input is underlined and parameters are enclosed in single brackets):
@ENTER-DIRECTORY,211056-<lang> FLOPPY-DISC-<drive> <floppy unit> @(211056:FLOPPY-USER)SSY-INST-A
The installation procedure will now start. It is self-explanatory.
How to update your HENT-MODE, LOAD-MODE and STOP-MODE files
When you install the system, remember to insert
@MODE (ND-OPERATIONS)SPRINT-LOAD:MODE,,
in your HENT-MODE file, and
@SPRINT /STOP-SPRINT
in any STOP-MODE files, and
@SPRINT /START-SPRINT
in your LOAD-MODE file, after the START-SPOOLING commands, but before any appending of SETUP-files for the printers (this is important because otherwise the running of SETUP will be aborted and the printer will be incorrectly initialized). NOTE: Remember to run SETUP-files with status 'UNCONVERTED' if you append them to the SPRINT-queues.
Date
Date of release, production, revision.
Date: 1987.05.15
Media
Labels
Images
Images (made with dd) of 5.25 inch floppies.
or all in a zip file